Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Cary Homeowners
If your chimney is pulling away from the house, staining the ceiling below the roofline, or dropping grit into the firebox, the problem is structural – and it isn’t going to fix itself with another season of burning. Chimney repair in Cary means finding out exactly what failed: the crown, the flashing, the flue liner, the masonry joints, or some combination. We do that diagnostic work before anyone quotes a number, and we show you what we found on camera.

Our technicians have up to 9 years of experience, and every job they run is a chimney job. We’re not a general handyman outfit adding chimney work to a long list; sweep, repair, and inspection are all we do. We install industry-grade materials from HeatShield, DuraFlex, Gelco, Olympia Chimney, Famco, and Copperfield, the products most generalists never carry. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (833) 519-6077 to get started.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a protective cover over the flue opening, and it’s the cheapest protection your chimney can get. A cap keeps rain, leaves, squirrels, and nesting birds out of the flue while still letting smoke escape. In Cary, where pine and hardwood both drop debris through fall and winter, an uncapped flue fills up fast – and a blocked flue is a carbon monoxide problem, not just a draft problem. We measure the flue, select a cap from a line like Gelco or Olympia Chimney that fits the opening and the appliance, and secure it against wind. A cap install typically runs $175-$450 depending on flue size, cap material, and whether a multi-flue chimney needs more than one.
Single-Flue Caps
Most wood-burning fireplaces in this area take a single-flue cap sized to a standard clay tile. We check the tile for cracks before mounting, because a cap over a broken tile just hides the problem.
Multi-Flue and Custom Caps
Chimneys serving a fireplace plus a furnace or water heater flue need a single cap built to cover all openings with a screened skirt. We size these to the full chimney footprint so nothing is left exposed.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is the removal of a failed or missing cap and the fitting of a new one, and it’s usually needed when the old cap has rusted through, blown loose in a storm, or gone missing entirely. It’s also worth doing when the existing screen has torn and birds or squirrels have moved in. We check the flue crown while the old cap is off, because a new cap on a crumbling crown is money wasted. We fit replacement caps from Gelco and Olympia Chimney, sized to the flue rather than the hardware-store shelf. Replacement typically runs $200-$500 depending on cap style and how much of the old hardware has to come out first.
Rusted or Collapsed Caps
Steel caps rust from the inside out, so a cap that looks fine from the ground can be paper-thin by the time we get a ladder on it. Rust staining on the chimney top is the tell.
Storm-Damaged Screen and Hardware
When a cap has come loose, the screws often wallow out the holes in the flue tile. We repair or rebuild the mounting point so the new cap sits tight.
Chimney Liner Installation
Chimney Liner Installation is the fitting of a new flue lining inside the chimney, and it’s the repair that matters most for safety when the existing clay tile is cracked, spalled, or missing. A damaged liner lets heat and embers reach combustible framing; a gas appliance in an oversized flue can also vent poorly and produce carbon monoxide. We install DuraFlex flexible liner systems, sized to the appliance so the flue drafts correctly. Liner installation typically runs $2,500-$5,500 depending on flue height, liner diameter, insulation needs, and whether an insert has to be pulled and reset. We also use HeatShield resurfacing for liner repairs where a full reline isn’t necessary.
When a Reline Is Necessary
Cracked tiles, missing mortar joints, and gaps between the flue and the surrounding masonry all point to relining. We show you the camera footage before you commit.
Liner Sizing by Appliance
A wood insert, a gas appliance, and an open fireplace each need a different flue size. Oversizing a liner causes poor draft just as surely as undersizing one.
Chimney Flashing Repair
Chimney Flashing Repair is the sealing and rebuilding of the metal that joins the chimney to the roof, and it’s the most common source of chimney leaks we see in Cary. When flashing pulls loose from the roof or from the mortar bed in the chimney, water runs down the outside of the flue and soaks into the framing. Brown ceiling stains, damp insulation, or rust on the firebox damper all trace back to it. We rebuild the flashing in layers with proper counter-flashing and sealant, or replace it entirely if the metal has corroded, and we coordinate with the roofer when shingles need to come up. Flashing repair typically runs $400-$1,200 depending on roof pitch and how much shingle has to be disturbed.
Leaks Around the Roof Line
Water that appears on a ceiling hours after a rain usually starts at the flashing, not the roof itself. We trace the leak to its source before touching anything.
Storm and Impact Damage
Falling limbs and wind-lifted shingles can tear flashing away from the chimney. Hail is uncommon here; wind and debris are what we see.
Chimney Crown Repair
Chimney Crown Repair is the rebuilding or resealing of the concrete cap at the top of the chimney, and it’s what keeps water out of the masonry itself. A cracked crown lets water run down through the brickwork; after a few freeze-thaw cycles, the face of the brick spalls and the mortar joints open up. We rebuild crowns in proper mix with a drip edge so water sheds off the edge instead of running back under it. Crown repair typically runs $350-$1,200 depending on crown size and whether we’re resealing a hairline crack or pouring a full rebuild. Small cracks can often be sealed; wide cracks or a crown pulling away from the flue need replacement.
Cracked and Spalling Crowns
Hairline cracks are worth sealing before they widen. Once a crown is crumbling or separating from the flue tile, a rebuild is the only fix that lasts.
Crown Rebuilding and Sealing
We form a new crown with the correct slope and overhang so water leaves the chimney instead of soaking in. You get a photo of the finished crown from the roof.
Chimney Repair Companies
Chimney Repair Companies vary a lot in what they can actually do, and that difference shows the moment the job moves past cleaning. A sweep-only operation can clean your flue and diagnose problems, but if the repair needs a reline, crown rebuild, or masonry work, that work goes out to another outfit – and you’re now managing the handoff. Because we handle sweep, repair, and inspection as one specialist, there’s no subcontracting and no finger-pointing. We install HeatShield resurfacing and DuraFlex liner systems, the higher-skill repair materials that separate a diagnostic-only service from a full restoration provider. Repair pricing is set per job by the written estimate after our camera inspection, and we say plainly when work can safely wait.
What to Ask Before You Hire
Ask whether the company does the repair itself or farms it out, and whether it carries insurance. Ask to see the camera footage before approving any work.

Full-Service Capability Versus Sweeps
A sweep who also relines and rebuilds can solve the whole problem; a sweep who can’t will stop at the diagnosis. We do both, so one call covers it.
Chimney Masonry Repair
Chimney Masonry Repair is the rebuilding of the brick, block, and mortar joints that make up the chimney structure, and it’s what keeps the chimney standing against wind and weather. Cracked mortar joints let water in that freezes, expands, and blows the brick faces apart – a slow process that gets fast once it starts. We repoint mortar joints, replace spalled brick, and rebuild at the roofline, matching materials to what the chimney already uses so the repair blends in. Masonry repair typically runs $500-$2,500 for common repointing and partial rebuild work, depending on height and how much square footage needs attention. Where the flue is intact, HeatShield resurfacing lets us restore the interior without demolition.
Repointing Mortar Joints
Crumbling mortar between sound brick is a straightforward repoint. Left long enough, water penetrates and turns it into a rebuild.
Rebuilding at the Roofline
The course of brick just above the flashing takes the most weather. We rebuild that section, re-flash the joint, and tie it back into the sound chimney above.
Brands We Service
We install and service DuraFlex flexible liner systems, which are the standard for relining when the existing flue tiles have cracked or when a new appliance needs a properly sized flue. We know how the liner loads, how the connections at the top plate and appliance collar wear, and where leaks develop when the installation wasn’t insulated properly. We also work with HeatShield chimney resurfacing, which restores the interior flue surface without a full teardown, and we service components from Gelco, Olympia Chimney, Famco, and Copperfield for caps, covers, and hardware.
Each of these product lines asks for its own handling, and installing them wrong is exactly how a repair fails early. Time on a given brand shows you the wear points, and it shows you the shortcuts the last installer took. Whether you have DuraFlex or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Crumbling mortar or loose brick at the roofline. If you can pick mortar out of a joint with a screwdriver, water is already getting in and the chimney needs attention before winter.
- Water stains on the ceiling or chimney face. A brown ring near the chimney chase points to a flashing or crown failure. These get worse fast and rarely fix themselves.
- White chalky stains on the brick. That’s efflorescence, a sign of ongoing moisture penetration. It means water is moving through the masonry and needs a source fix.
- Soot stains or a broken cap at the flue opening. An open or damaged flue invites birds and debris, and a blocked flue raises carbon monoxide risk.
- Smoke backing into the room or a weak draft. Poor draft often points to a flue size, liner, or blockage problem. That’s a diagnostic job before it’s a repair job.
Our Process, Step by Step
Our chimney repair process is built so you always know what we found, what it means, and what it will cost before any work is done. Here’s what the job looks like:
- 1
Book the visit. We take your address, ask about the appliance, and schedule a time for a technician to come out. Call (833) 519-6077 to book; we answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
- 2
Camera inspection. We run a camera through the flue and photograph the crown, flashing, and masonry from the roof and ground. You see the footage with us and we explain what it shows.
- 3
Photo report and written estimate. Everything goes into a written estimate with the price set per job. No pressure, no surprise line items. If a problem can wait, we tell you it can wait.
- 4
Schedule the repair. Once you approve the estimate, we book the repair and confirm the materials: DuraFlex for a reline, HeatShield for flue resurfacing, or replacement hardware from Gelco, Olympia Chimney, Famco, or Copperfield for a cap.
- 5
Repair and final check. We complete the work, run a final camera check, and leave you with photos of the finished result. If you’re selling the home, that documentation goes with the inspection report.
How Much Does Chimney Repair Cost in Cary?
Chimney repair in Cary typically runs from $175 for a simple cap install up to $5,500 for a full reline, with most repairs landing between $400 and $2,500. A typical cap replacement runs $200-$500 depending on cap style and old hardware. A flashing repair runs $400-$1,200, mostly driven by roof pitch and shingle disturbance. Crown repair runs $350-$1,200, and masonry repointing runs $500-$2,500 by square footage and height. Liner installation runs $2,500-$5,500, the widest range because flue height, liner diameter, and insulation all move the number.
What drives the price: how high the chimney is, how much of the structure needs replacing versus sealing, roof access, and whether the repair needs specialized materials. To avoid overpaying, insist on the camera evidence before approving anything: if a company tells you that you need a new liner, they should be able to show you the cracked tile on camera. Every estimate we write is free, and the written estimate sets the final price. We also tell you plainly when a problem can wait a season.
Our Service Area Near Cary
We serve Cary and the surrounding towns throughout the Triangle. If you’re in Durham, Raleigh, or Youngsville, we cover that area too, and we reach Carolina Meadows, Moncure, Broadway, Buies Creek, Mamers, and Coats as well. For nearby repairs, our chimney repair and chimney repair pages show what we handle in those communities. Book a visit and we’ll confirm arrival timing when you call. For the broader sweep and inspection picture in this area, see the Chimney Sweep Cary page and our chimney repair service.
Serving Cary, NC – Our Local Coverage Area
We serve Cary and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Cary
Chimney repair is any work that restores the structure, flue, or drainage of a chimney after wear or damage. It covers crown rebuilding, flashing repair, masonry repointing, cap replacement, and liner installation. Cleaning removes creosote; repair fixes the parts that keep the chimney safe and standing. We diagnose first so the repair matches the actual failure.
Most repairs take one visit, usually two to five hours depending on scope. A cap install or flashing repair is often a single visit; a full reline or crown rebuild can take longer and may need a second day. We tell you the expected time when we schedule.
Repair costs in Cary typically range from $175 for a cap install to $5,500 for a full reline, with most jobs between $400 and $2,500. The written estimate sets the final price, and it’s free after our inspection. Call (833) 519-6077 for an exact quote.
Yes, we install and service DuraFlex flexible liner systems for relining and code-compliant flue upgrades. We also work with HeatShield resurfacing and components from Gelco, Olympia Chimney, Famco, and Copperfield. Whether you have DuraFlex or another make, we can help.
Same-day service is available when the schedule allows. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Warranty terms depend on the work and the materials installed, and we confirm those terms in writing with your estimate before any work begins. We don’t promise terms the manufacturer hasn’t confirmed. Ask us at the estimate stage and we’ll spell out what applies to your job.
Clear the area around the fireplace and make sure we can reach the roof and the flue opening. Move fragile items away from the hearth and secure pets. If you have photos of any staining or leaks, have them ready; they help us trace the problem faster.
Schedule Your Chimney Repair Service in Cary Today
If you’ve spotted a leak, a crumbling crown, or a flue that needs relining, get an expert set of eyes on it before the first fire of the season. We inspect with a camera, show you what we find, and give you a written estimate with no obligation. Call (833) 519-6077 to schedule. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Cary.